










CARPRO
CARPRO Washing, Decontamination and Nanotechnological Protection Kit
CARPRO Washing, Decontamination and Nanotechnological Protection Kit
Carismatix Srl
Via dei Laghi 24
36077 Altavilla vicentina VI
Italy
Take care of your car with the CARPRO Kit consisting of all the products needed for washing, decontamination and nanotechnology.
Lift is a concentrated alkaline foaming pre-wash perfect for removing large quantities of dirt from the bodywork before the shampoo phase making it much safer.
Descale is an innovative acid pH shampoo developed to remove heavy dirt, limescale stains and, in the case of hard, calcareous water, to balance it.
IronX is an innovative pH-balanced formula that works by chemically dissolving ferrous residues that have penetrated the paint. It can be used on glass, paint and wheels, including aluminum and delicate alloys.
Eraser is an advanced IPA capable of removing oils, silicones, polish and compound dust from all surfaces, ensuring maximum adhesion performance for C.QUARTZ coatings.
EliXir is a quick detailer that gives the bodywork extreme depth, shine and maximum hydrophobicity thanks to its ceramic nanotechnology-based composition.
C.QUARTZ UK 3.0 is the most refined and appreciated CARPRO nanotechnological coating on the market because it is able to provide very high performance both in terms of colour depth and resistance, despite the simplicity of application in humid and hot conditions.
Release is the first CARPRO wax-based nano-sealant, developed for the protection of newly applied ceramic coatings on car surfaces.
The Kit consists of:
- Alkaline Foam Prewash - Lift
- Acid pH Anti-Limescale Shampoo - Descale
- Decontaminant Spray - IronX
- Isopropyl Alcohol Defect Check and Pre-Application Sealants - Eraser
- Quick Detailer - EliXir
- Nanotechnology Coating - C.Quartz UK 3.0
- Pre-Delivery Sealant - Release
- Microfiber Cloth - 2Face
- Microfiber Cloth - 2Face Lite
Racconta la tua esperienza e aiutaci a migliorare sempre di più!
How to use it BEST
///
USAGE INSTRUCTIONS
1. Make sure the surface is cool and not exposed to the sun.
2. Dilute Lift with water in a ratio ranging from 1:10 (with Foam) to 1:50 (with Spray).
3. Spray from bottom to top.
4. Let the product sit on the surface for a few minutes before rinsing. Do not let the product dry, even if diluted.
5. Dilute Descale according to the extent of limescale contamination from 1:50 to 1:100 for bucket washing or from 1:5 to 1:10 for foam lance. For light contamination: use Descale with foam lance and wait a few minutes before rinsing. Then proceed with hand washing. For heavier contamination: wash panel by panel. Wash the panel and let the product rest for as long as possible without drying. Repeat if necessary.
6. Rinse with water.
7. Spray IronX on the affected surface and wait 3-5 minutes. Contaminants will change color to purple red.
8. If necessary, use a brush, a brush or a damp sponge. Rinse with water.
9. Spray Eraser on one panel at a time, leave to act for 20/30 seconds and remove with a clean, soft microfibre.
10. Wrap the microsuede around the grey part of the applicator and dispense 5-6 drops of UK 2.0.
11. Spread the product over areas of 50x50cm.
12. Remove the product immediately after or at most after 2 minutes (depending on the ambient temperature and humidity), making sure that all residues have been eliminated.
13. To increase performance, apply a second coat 1 hour after applying the first.
14. Any drops of water during the first 48 hours must be removed before the protective product has completely dried to avoid the formation of stains. To avoid this from happening, it is recommended to apply Release 4 hours after applying CARPRO C.QUARTZ UK 3.0.
15. Spread Release evenly over the surface using a microfibre cloth.
16. Use a second microfiber buffing cloth to remove any residue.
17. Spray Elixir sparingly onto a microfiber cloth.
18. Spread it evenly over an area of approximately 100x100cm.
19. Remove residue with a second clean microfiber.