A professionally performed motorcycle wash helps maintain the condition and value of your motorcycle. original of the vehicle and to protect it adequately over time, just like for cars, with the necessary differences to consider.
Take into account the presence of more delicate components, which must be treated with particular care and for which the decontamination phase and aggressive products are not recommended as there is a risk of degrading them seriously.
So let's see what steps to follow for a correct detailing of the motorbike.
/// PREWASH (Phase 1)
Before starting with the actual pre-wash, it is necessary to check for any insect residue or midges. In this case we suggest proceeding with a specific pre-detergent that softens or dissolves the lightest contaminants. We recommend Cartec Insect-remover or CARPRO BugOut , which only need a little water to work. a couple of minutes before rinsing them.
Pre-washing is necessary to almost completely eliminate dirt and impurities. It is therefore a good idea to start with a APC , like CARPRO MultiX , Cartec All Purpose Cleaner or Exterior Multi Cleaner (ready use). Simply spray the product over the entire surface of the fairing. To make the process more effective, it should used a brush in the more intricate areas of the bike, taking into account that the vehicle has shadowed spots where the cleaning solutions take longer to reach than a car body.
It is also important that the chain is not cleaned directly: if washed in detail it would lose the oil to keep it lubricated, the latter should be washed ad hoc over extended periods if necessary. In the event that If you wish to degrease it, proceed with Cartec Engine Wash , applying lubricant immediately after.
Once the product has been left to act, proceed to rinsing, always starting from the bottom upwards and doing Be careful that foam and dirt slide off all surfaces.
/// WASHING (Phase 2)
The time has come to finish cleaning our motorbike. First of all it is essential to analyse the type of dirt to determine which shampoo to use:
- Does the bike have limescale stains, mud and other mineral deposits? In this case you will need a detergent at Acid pH like CARPRO Descale .
- The bike already looks almost completely clean? The ideal solution is a pH product Neutral, such as CARPRO Reset , CARPRO HydrO2 Foam or Cartec Wash & Wax . The latter are also characterised by a protective action.
At this stage, the common rules of detailing apply. We recommend using the double technique bucket with grid (read the dedicated Guide ) as it is effective and safe, alternatively you can follow the rules basics:
- Pour some water into a bucket.
- Pour in the chosen shampoo, following the indicated dilutions.
- Completely fill the bucket, in order to obtain thicker foam.
The washing phase involves a mechanical cleaning process using a glove or a sponge . The most convenient choice right and used in this situation is a microfiber material, safe and delicate on surfaces.
During this phase, if necessary, you can focus specifically on some parts of the bike, such as rims and tires , using a specific brush or a brush for points more difficult to reach. In this step we suggest starting from the inside of the circle, without neglecting the brake caliper, and finish by rubbing vigorously on the tires.
After rinsing, you can proceed with drying.
/// DRYING (Phase 3)
Drying is not to be underestimated, especially if you want to end up with the best results, avoiding the formation of halos caused by impurities in the water.
A good cloth in Microfiber specifically for drying is ideal, as the fibers create a sort of shield for particles of dirt. It is important to start from the top, working down and avoiding applying pressure.
For a professional result we recommend finishing with an air blower . This extra precaution is necessary due to the peculiar shape of the motorbike, with numerous recesses and intricate points to reach.
/// PROTECTION AND MAINTENANCE (Phase 4)
We have finished this thorough wash of the motorbike, which will now be sparkling and free of defects: we want maximize the effect and ensure that the finish obtained lasts as long as possible?
It's time to apply a protective product.
A quick and easy step that can also be implemented as a routine at the end of a periodic wash is the use of a quick detailer such as EliXir by CARPRO or Quick Spray Wax by Cartec . It will give the vehicle gloss effect and hydrophobicity in an easy and fast way, as to apply it you will only need two microfibre cloths (one for applying, the other to be used later for removing), spray it sparingly on the cloth and spread it over an area of about one square meter at a time.
Let's now move on to the protection of plastics . For this job we have designed a special kit with selected tools and products: Plastic protection kit for motorcycles and scooters .
Thanks to this combo of Cartec solutions, the parts that tend to wear out more easily, such as bumpers and tread, get a light restoration combined with the protective coating and the color reviving effect. We recommend that you consult the Instructions for Use before using the products.
